IQShield 3 Pack for Samsung Galaxy S20 Ultra (6.9 inch) Screen Protector (Case Friendly) Easy Install Smudge Resistant Anti-Scratch Ultra Thin Anti-Bubble Clear TPU Film

I wasn't sure if this screen protector would work on my phone as the curved edges are notoriously hard to cover, but I'm blown away with ease of installation and the final result. It's nearly perfect, not a single bubble and the whole process took less than 5 min (not including the overnight drying). I can barely tell that there is a screen protector on my phone. It's clear, shiny and it covered the screen from end to end, even the curved areas. Amazing! I did watch the how-to install YouTube video as suggested in the package and it helped me with determining how much liquid is enough for this process. This was my first "wet" installation so needless to say I wasn't sure how to or what to expect from this process. This is how I did it in steps: I did this process at night right before I went to bed to allow the screen protector to fully dry overnight as suggested by the seller. I cleaned a desk surface to remove any dust and/or hair and lint, removed the phone case and my old screen protector. I washed and dried my hands and then I sprayed some of the liquid on my fingertips to remove any possible residue and lint/hair (as suggested in the installation video). Then I used the cloth and sprayed some liquid on it and cleaned the phone screen until it was shiny and lint free. Then I peeled off the backing from the screen protector and held it up vertically with my fingers while spraying it with the liquid. I made sure that the protector is completely soaked with liquid. I held it up until the dripping stopped (and to not get any excess on the phone speaker and other openings) and then just gently laid it on the phone screen. At this point the screen protector was completely flat and bubble free. I gently moved it around (without stretching, just a very gentle push) until it was perfectly aligned with the edges, camera and speaker openings. At this point the protector wasn't sticking to the curved edges, but as instructed I waited a few minutes and then gently pressed it with my fingers until it started to adhere to the edges. Once everything looked good to me, I used the squigee that was included in the package and just gently made a few flat moves across the screen and again over the edges from the middle out to make sure all the liquid is pushed out. Once I was sure that there was no "lifting" on the corners and edges, I laid it flat on my desk and went to bed. I was extremely happy to see the final result this morning. Just perfect. No bubbles, no lifting, no rainbow screen effect, no glare, not dimming, and fully covered curved edges. I popped my case back on it and it still fits perfect. For a reference I have Spigen Tough Armor case on my phone and this screen protector is compatible with it. I definitely recommend this screen protector.

I have had I.Q Shield screen protectors on 3 of my phones spanning about 5 years in total. If you're looking for a good screen protector, this is one of the best you can get. In my own opinion I would say that this is one of the best that you can't get and it comes at an extremely cheap cost. They make some claims regarding their protectors and I will go over some of those below. Pros • At this price, you are getting an amazing deal for what you're paying. Their customer service is honestly one of the best around, and the quality/quantity of the screen protectors you get is unbeatable. • Yellowing: These screen protectors calim to not turn yellow over time and this is honestly true. Within the whole span that I had my first screen protector (about 2 years) it remained pretty clear and transparent. • "Self healing" from scratches: This is one claim I myself was not sure about, but also holds up. I actually made a couple scratches with a nail and while the imprint didn't go away immediately, it did fade away and turn fairly normal again after a day or two. It is also fairly safe to have this in a pocket with keys, but be careful with your front facing camera if you do. Cons • Fingerprint: While I have had no problems scanning my fingerprint after installing this screen protector, some people might. This might be because of a small mistake during installation, or like in my case mostly because of the phone itself. I know because I had the same problem before installing it. • Anti Bubble: While this is almost one of the easiest protectors to install, and one of the ones I have had practically no bubbles appear under, it does happen. However, I never had trouble with a big or noticeable bubble remaining. Even small bubbles are very easily fixed by continuing to use the squeegee provided on the package to get the bubble out, but I did want to mention it. 50/50 • Installation: As far as the installation goes, this is pretty easy. The main problem I had was having to squeegee out the liquid used for the installation (you spray the screen protector with it) and not just immediately being able to use my phone. Honestly, this is not a significant drawback though. I would highly recommend this product if you are still on the fence about buying it.

The product is good, however....when I was applying the screen protector the solution got into the charging port. They suggested you apply the screen protector before bedtime since it needs time to adhere. I applied it at the end of the day, when my phone was ready for a charge. When I put my phone on charge, I got an error message saying it had detected moisture and could not charge me phone. When you squeegee out the solution, it drips down and must have gotten into the charging port. I have a S9 and assumed it's waterproof....I guess not. It took me a while to get my phone to charge, again. Definitely created a lot of panic. I contacted the seller to tell them about what happened just to keep them informed. I got a reply back, asking if I would like a replacement product?????

This screen protector is the best buy for a film curved screen protector. It is truly easy to apply and makes and excellent bond to curves on the edges of my Galaxy S8. Because it remains slideable when first wetted it can be positioned perfectly to fit the openings of the phone. You probably have about 5 mins before it starts bonding to the screen. I watched the instructuon video twice and then applied it with minimal problems. There is a small but unnoticeable bump on the film but the edges stuck on very well. I ran my wet hand back and forth the two sides of the curved phone to ensure that it stuck well. I left the phone off for about 10 hours and did not put the case back for 13 hours. FYI, the case is a UAG one-piece case. I have had the screen protector since May 10 and so far it has been perfect. I also find the touch sensitivity to be better than either of the two different brands of ballistic glass protectors I had on this same phone (both of which fell off). Highly recommended!

Best Screen Protector i have used comes with a second one but the first worked well and i would buy this product again.

Very good fit inside of my Quadlock (motorcycle mount) case & it has held together great around all of the edges after several weeks of use. This is the reduced screen coverage that a "case friendly" screen protector is supposed to have.

The product was supposed to be case friendly but it’s not! The bottom part of the protector peals off as it touches the case (I use speigen). Disappointed, because I researched a lot and found this MENTIONED to be the best screen protector for galaxy s8. Also the seller Exborders is least bothered to help with any info on fixing it