SGILEPro 9/1 Network Tool Kit, Ethernet LAN Cable Tester Crimper Repair for RJ45/11/12 Cat5/5e with Connector Accessories

A great product and a fantastic value. I just moved into a newly constructed house. There are 8 Cat5 jacks throughout the house but they left me with all the wires unlabeled with no terminals. I purchased this kit in the hopes I could finish the work myself. The kit came with everything I knew I’d need but also something I didn’t. Ok, there’s a small learning curve and I didn’t do well on my first two attempts but I quickly learned and every one after that went perfectly.After attaching the plug I plugged it into the master test unit and then went through the house with the remote until I located the connected jack. Simple.I even discovered that one of the jacks had a bad connection and I was able to use the “push-down tool” (the thing I mentioned not knowing I’d need) to fix it. I can only imagine how much money I saved by not having to hire someone to come in and do the job.Ok, here are my two tips. First, do your best to completely straighten out the twisted wires and lay them flat and as tightly together between your forefinger and thumb and them cut them straight across to make them COMPLETELY even. Then inserting them into the plug should meet only slight resistance. If you have to force it you probably have something out of alignment.Secondly, after you firmly crimp the plug with it fully inserted into the tool, release the pressure only enough to allow you to pull the plug back out SLIGHTLY and then apply crimping pressure again.The components is this kit and even the case it comes in feel high quality. The tester is not just a continuity tester, it actually has some smarts built in and I would have been willing to pay as much for it as I did the entire kit.Great value and great results.

I got this for a networking project where I ran 40+ RJ45 drops.Let me break down what I used and didn't use.Tester: Used for RJ45. Worked great. The only thing I wish it did was automatically switch ports at the patch panel so I didn't have to run back and forth so much. :D But this was the main reason for getting this kit. I wanted a tester that would work well to make sure I wired everything correctly. It was a success.Crimper: Used for one cable. It worked. No complaints, but that was only one cable.Terminals: These are mostly metal. Very sturdy. Other than crimping them and testing them, they seemed to work fine. I used the cable for testing each drop.Yellow wire stripper. Worked great. It did not cut a single wire inside the cover. The depth of the cuts was perfect.Zipties. These were a little weak. I used almost all of them, but if you pulled hard on them, they'd break. Not sure how long they'll survive in the ceiling/walls if they have anything get caught on them.I didn't use any of the other components of this kit, so I can't rate anything else. I had another punch tool and this was going to be the backup, but my main punch tool was great, so I didn't need it.

I bought this kit because I was planning to run some Ethernet lines through my house and I needed the tools to do it. This kit had the two tools I really needed, a crimper and a punchdown tool, and was inexpensive. Since I'm using them for what is pretty much a one-time job, I was looking for low cost over super-high-quality.Overall the kit is pretty decent. The crimper, stripper, and punchdown tools all seem well made and the included RJ45 connectors are shielded, which was a nice surprise, though they are sized for Cat-5 cable and I'm running Cat-6, so I can't use them for this project. The kit includes additional odds and ends that will prove useful, like cable ties and an RJ45 coupler.My only complaint with the whole kit (and the reason I deducted a star) was the cable tester. This wasn't the reason I bought the kit in the first place, and I wasn't really expecting much from this tester, but it seems to have worked for about 5 tests before crapping out. I had a bunch of old Ethernet cables lying around and I wanted to see which ones were good, so I started testing them. One of my cables had a broken clip, so I cut it off and repaired it (manly for practice, as I haven't crimped a cable since taking data communications classes in college some 15+ years ago). After fixing it, I put it back on the tester and the thing got stuck on the "1" light. I tried some of the other cables that tested fine before and they also got suck on "1." Despite this, I plugged my repaired cable in to a switch and successfully connected a computer to the network, so my fix appears to have worked. Not the end of the world, though the tester would have come in handy when I start to terminate the cable I pulled.Overall, it's a pretty decent kit, I just don't recommend buying it for the cable tester alone.

This has EVERYTHING you need to run Ethernet in your home, including a healthy number of RJ45 ends.The crimper/cutter tool can also do RJ11 ends if you are looking to make phone cables. The kit did not come with RJ11 ends, though. Thus far, I've used it to make both a phone cable and an Ethernet cable. Both work flawlessly.The RJ45 ends it comes with are shielded, which is a nice touch, and the rubber protection jackets prevent the plastic tab from getting ripped off.The jacket cutter tool is extremely sharp and works great.Haven't used the tester yet - it takes 9V batteries, and I don't usually buy them.... I personally didn't feel the need to test right now, but in the future it will be handy if I run into troubles.I also have not used the punch down tool, but it seems to be hefty and high quality.The zip ties don't seem to be of the highest quality, but honestly they are just icing on the cake.If you are looking to DIY some hardline Ethernet in your home, this kit and a 1000 foot box of Cat5E or Cat6 are what you need. 10/10, would recommend.

This kit came in handy when I was setting up my security cameras around my house. The electronics store only sold the ethernet cables in packets of 100ft and 50ft packs with the connectors on the ends. Sometimes after running cable to cameras I would have the roll up the excess cable and use a tie wrap to secure it. The work was an eyesore at times and not to mention could be pulled. This kit was really easy to use, the instructions were clear..... You really need to ensure you unravel and get the cables to line up on the proper color order and the multi tool does all the rest.... The Tester worked well letting me know there was proper connectivity.... This make my DIY installations a breeze..... I've spliced and made up about 10 cables of varying lengths for security cameras thus far..... And all the installations were neat..... No excess cable and all crimpped perfectly on the first try...... Great value for money.