283in PVC Wire Covers for Cords on Wall, One-Cord Cable Concealer Kit, Paintable Cable Raceway Management, Cord Hider, Max for 2 Small Cords for Home Office, W0.59in H0.4in

This cord concealer kit was exactly what I needed to clean up the mess of wires behind my wall-mounted TV. The channels are sturdy, spacious, and well-designed, easily fitting multiple cables like HDMI, power cords, and speaker wires. Installation was simple—just peel and stick with the included adhesive (or screw in if you prefer). The covers snap on securely but are easy to remove if you need to make changes later. I also love that the PVC material can be painted, so it blends perfectly with my wall color. The 125-inch length across 8 pieces gave me plenty of coverage, and the included connectors and corner pieces made it easy to work around edges and angles. If you're looking for a neat, professional-looking solution for hiding cords in your home or office, this kit is a great value. Highly recommended!

Wow! This worked Fantastic, and did what it said it does! Great product. Easy to use, & held all the wires I wanted in one unit (tight fit) instead of running two rows. I had 2 sets 18g red/blk jacketed plus 2 skinny sets jacketed red/blk speaker wires. You should ***pay Attention*** putting the correct part to the wall. One side (cover) has slight rounded edge & the backside has a straight flat edge. I didn't pay attn & some weren't lining up as smooth because I had put coverside to wall. No one would probably notice but it bugged me knowing it was wrong, lol, so I pulled off those pieces to redo. Which brings me to the double sided tape included, which is great & 'Strong - I didn't want hassle of using screws. ***Note IF you need to remove because of error, use a hairdryer on the plastic to warm up tape underneath to be able to pull off the wall, otherwise you might take part of wall.*** Thankfully I saw someone else mention this trick and worked like a charm! This does of course destroy the piece, but i had plenty extra & glad came with w/ 2 rolls of tape.

I love it and it does what it says. I gave it 4 stars only because it did not have enough of the straight connectors and you cannot buy just the straight connectors. To get them you have to buy a whole set. Aside from that it works well, does what it says and it is easy to use and install. It made my tangle of cables look neat and my wall and floor finished. I can recommend this product

Overall, I'd recommend this kit as it is well made, does the job and can cover a lot of space. I could see, however, that the installation might be tedious for someone not accustomed to figuring things out and the directions are no help. For example, it's not clear which side is the base and which is the cover (the cover fits OVER the base as shown on the outside of the box). Also, each of the covers must be cut shorter than the base as they fit partially into the joint covers, so you'll have to cut each cover even if you're using full runs of the base. Be careful not to abut the bases too close to woodwork or inside corners or you may not be able to snap the cover over the base. Once it's all done, it looks neat and tidy. I'd definitely buy it again, but I have a lot left over from my first install, so that's pretty good value.

Just what I needed for my project & easy to install

I purchased three of these kits to run two flat ethernet cables from a closet in my bedroom where my network is located. I was able to run the system along the baseboards and have it barely noticeable. I had to run over two different door frames in order to reach one location I needed, and across the ceiling to reach another location. Unfortunately as it's designed for 1 cable, there's no three way splitters included. Even though it can easily handle two flat ethernet cables. So in one T junction I had to leave the wires exposed. I also had to leave them exposed under the doorways as there's no clean way to implement that. The ethernet cable I purchased came with those small hooks that have a nail in them, and I was able to put both cables together with two of those under the doors very cleanly into the next wire covers. The adhesive is very plentiful as well, and some of the best Two faced tape I've ever worked with to take off the second sides piece. I was able to easily use my thumb nail to get the plastic off it and stick it to the wall. It did take a bit of work to get things lined up correctly, but I used the straight line pieces that came with the kit as spacers from the baseboards. Basically I would stick one on, get the next piece ready and then stick it in position. When I finished I had to go back through and take the covers off everything to put the cable in, but it seemed like the best way to ensure everything was lined up perfectly. I even did a small diagonal piece and the way the sections are made they can hide completely in the connector pieces. Very nice kit, especially for the price.

This fits only one single cable!! Make sure you check the connection prices and covers are in Place and fit snug before adhering to wall/ceiling. The adhesive tape they provide Is extremely difficult to remove without tearing off the wall texture. (This is the mistake I made) then I tried to heat up the area to help with tape removal and ended up melting these plastic pieces together creating a difficult mess to remove. They are too short for the length I want to cover and it does not look good having a connection piece every 12inches so I going to have to spend the money or cost to do it the right way. 🥺 these would work great for others and small coverage needs.

These really had chords well. And easy to install.

Decent product that looks good, however it has 18 lengths and only 14 straight connectors. That means that unless you use three “elbow” connectors you are going to run out of connectors. To make matters worse, I had to cut a few lengths in half which means I am missing even more of the connectors needed to use the full kit.

I recommend the product.

I like the design of this better than some other cable covers which are relatively huge by comparison (and usually end up mostly empty), this is a lot more stealthy. It can fit a 14 gauge dual conductor wire with a large in-wall rated jacket but that's about it - still it's a lot thicker cable than I expected would fit through one channel. It comes with everything you need including connectors both straght and angled, and even tape to adhere the channels with. The channels are two parts, the part that goes against the wall and then a top cover for it - it's possible to snap the top cover over the bottom part but it's difficult and much easier to slide it from the side, but this is not very practical. Still, it's a lot better than having to try to fish cords all the way through a closed channel. The only thing I don't like about the kit is the connectors to join multiple pieces together, they're easy to use relatively and the channels just sort of slide into them, but each channel is short so you have these ugly bumps at pretty regular intervals along the run which I'm not a fan of. The other thing is that it's nice it comes with adhesive tape right in the box to use it, but I know from experience using this type of tape that it will absolutely destroy any paint you use it on so use it sparingly and wisely you are not going to want to have to reposition it after you put it on because it will take the paint off with it.

It’s not meant for hiding a huge mass of cables so it’s not as useful in some setups. If you just need to hide one length of cable, it’s perfect! Other than some planning and measuring, installation is straightforward and simple. Apply the adhesive tape to the back of the cable raceways, section by section, and apply where you want it. Insert the cable right away or snap/slide the covers in place as you work. A different cable concealing kit I have included the option to screw mount the cable raceways instead of relying on adhesive tap, but that's not an option here. In this cable concealing kit you get 304 inches of cable concealment. This includes: 18 x cable raceways (16.9 inches in length each = 304.2 inches) 14 x couplings/connectors 6 x flat elbow connectors (for making a 90° turn/angle along a wall) 2 x inside connectors (for connecting raceways in the corner of a room) 2 x outside connectors (for connecting cable raceways over a corner edge) 2 x rolls of adhesive tape

This is a comprehensive kit for concealing a single cable for almost any setup, with a total run length of just over 25’. The channels are very small – a 14AWG surge protector cable fills 100% of the channel. I’d hoped to use this upstairs since I only have a single (power) cord from the wall to TV, however the flat-style cord is too large for this channel (technically it fits, but twists the channel - see a photo attached). The channels easily fit a single 16AWG power or DisplayPort or HDMI cable, and could be used for a couple of speaker wires. The front covers snap on firmly. The couplings (which connect the 16.9” segments) fit over the segments, and will hide any imperfections caused if you’ve had to cut them down to size. Included are two rolls of double-sided tape. So far, I’ve only installed a single segment to hide a single HDMI cord running from my console to my TV (the other cords are run through a larger concealer channel). This size of concealer is ideal for a single standard-sized cable while maintaining as low of a profile as possible. If you have a larger single wire, you may wish to buy a larger channel kit. Overall, I’m really impressed with the build quality of this kit and how it looks when installed.