Descargar la aplicación
Servicios al cliente
Sobre nosotros
Copyright © 2025 Desertcart Holdings Limited
Descargar la aplicación
⚡ Elevate your vintage gear with precision power — no noise, all glow!
This High Voltage DC-DC Boost Converter transforms a 12V input into adjustable high voltage outputs ranging from 150V to 420V, alongside a finely tunable filament voltage from 1.25V to 12V. Designed for tube preamps and Nixie tubes, it features three potentiometers for precise voltage and current control, a compact PCB footprint, and high-frequency switching technology that guarantees noise-free performance, making it an essential power supply for audiophiles and vintage electronics enthusiasts seeking reliable, customizable power solutions.
| ASIN | B0992GCCSK |
| Best Sellers Rank | #270,172 in Tools & Home Improvement ( See Top 100 in Tools & Home Improvement ) #1,126 in Power Converters |
| Date First Available | July 9, 2021 |
| Item Weight | 4.2 ounces |
| Item model number | 12VBoost-HVPSU |
| Manufacturer | QINIZX |
| Product Dimensions | 3.54 x 2.16 x 1.25 inches |
| Specification Met | CE |
| UPC | 723258876523 |
G**S
Another batch of bad HV regulation.
Like most problems other are having. I purchesed 2 a few months ago and they work fine. I purchased two more last week and they are both bad. The HV regulation does not work. Either bad or damaged parts. Someone should notify the manufacturer to see if they can fix the problem, since it is a very useful power supply. I NEED IT!
S**0
Works well to power small guitar amp
I like this. I am using this to power a small vacuum tube amp that I built for my guitar. I can not crank to full voltage but I can get it up to about 200 volts and it runs a little warm but is stable and does not introduce noise into the amp. This works much better than having to have a high voltage transformer etc. You can run this off 12v batteries and get off the grid and play a tube amp without heavy transformers etc.
A**S
Vibration safety
Works Perfectly ! Coil must be glued by silicon!
D**S
Noisy
I'm using this to drive a 12AX7 tube circuit. There is a small-amplitude 14 Hz sawtooth on top of the HV, which shows up in the audio output. Bought two of these at the same time and both show this behavior.
J**Y
needs 12 v , what is really needed every where is 5-7 dc in
really should work at 5 vdc , to be valuable. All these supplies need 12 vdc and tubes have 6.3 v . So 12 v is another power supply for a power supply . Might as well stay 60 hz Also USB is everywhere 5 vdc 2 amps . yet no 90-200 v supplies made Can this be modified for 5-7 vdc input
S**T
The high voltage circuit of this product does not work.
The high voltage circuit of this product does not work. When powered at the recommended 12 Volts, the output voltage was not stable, either with or without a 100 kOhm load. Its current draw from a 12 V supply started at 1.15 Amps at 233 Volts, dropped to 0.36 Amps, would fluctuate suddenly from 0.4 to 0.8 Amps. Thereafter, I could only adjust the voltage from 140 to 178 Volts. Again, the high voltage was not stable. The low voltage circuit of this product does work and is adjustable. I set it to mid-scale, 6.6 Volts.
P**E
Engineer
Very good
P**N
Unreliable high voltage output and completely unstable
As other commenters have said, the high voltage is completely unreliable - after setting it at about 300V unloaded, it drifted way down below 190V over time. Loading it made no difference. The heat sinked transistor is also super hot and I think the board has a massive thermal instability. Do not waste your money.
Trustpilot
Hace 2 días
Hace 3 semanas