ROCKBROS Bike Water Bottle Holder Ultra-Light Bicycle Bottle Cages with Screws Tool, Universal Bike Cup Holder Rack for Road MTB Bikes…

I was excited to get this matches my new e bike perfect looks great my bottle fit perfectly.

I'm a little worried it will break because the plastic feels flimsy. But the installation was super easy, and it does hold my water bottle. It also flexes to hold *slightly* larger water bottles. I have used it a few times now with no issue. It looks good on my bike. I hope it lasts long.

Cages come with screws and an allen wrench, which made them super easy to install. So far they seem nice and sturdy despite being plastic. Time will tell. I'm using a 24 oz Polar bottle (which normally fits in a standard water bottle cage), and the only CON is that these cages seem a little bit too small. The bottle fits in them, but the bump at the top of the cage doesn't quite line up with the notch in the bottle. And the arms/wings do grip the bottle pretty tightly to the point that it's a bit difficult to get it in and out. It's too tight to get in and out while riding, so that's a bit of a bummer. I did decide to keep them though because I prefer a snug fit over a looser fit. The PRO is that the bottle will not budge no matter how bumpy the road. If you're bothered by loose bottles then this is definitely the cage you want. I've purchased some other Rockbros stuff and it all seems quality. My only recommendation to Rockbros would be to make the cage just a few millimeters bigger to properly fit the bottle.

This was the perfect bike water bottle cage I needed because it hold my coffee cup perfectly. The color is snappy and the material flexible. The installation was easy.

I bought this for my E bike and it fits perfectly and holds the water bottle size that I need! It has a nice sleek, red and black color. Sometimes it feels a little bit flimsy, but I've never had a break even if I put a little bit bigger of a water bottle in there so I feel very confident with this on my bike that my water bottle is not going to fall out! They also run a deal on a two pack! So great value for the money it works really well and it's super easy to set up and use!

--Think carefully if you want to risk permanent damage to your bikes only water bottle mount point. Mounting the cage was extremely tricky because of the location. It was tight and impossible to start the bolt with your fingers-you had to try and start it on the end of an allen wrench, which anyone with experience knows is a no-no. The fact that it so nearly fit -you could catch the first thread but only with the bolt at an angle- might cause frustration and the temptation to press on with just a little more pressure, a few more turns. If you do, you will cross-thread the bolt and could cause permanent damage. To repair it you would then be forced to try something like drilling it out and installing a 'riv-nut' -which would also be very difficult without a small right-angle drill and short drill bit and special installation tool for the 'riv-nut'-or you'd need to remove the rear tire and fender and.......!!! Kiss your soon to be frustrating afternoon or $$$ goodbye! To fix the cages I needed to use a 'rat tail' file to effectively lengthen the distance between the mounting slots on the water bottle holder. What should have been literally a 2 minute install for a 10 year old turned into a frustrating 30 minutes. Just FYI- it was definitely the cages cause I tried both from my order and both were too short. Both a 'no-go' on an Aventon and an old Schwinn as well -But much more accessible. After mods it took less than 2 minutes.... to do both...with loctite!! -you get the picture. The cages already use extended slots for mounting flexibility. I don't see that an extra 0.5 mm in slot length is going to alter the engineering. And it wasn't just plastic 'flash' from a seam line that could be easily removed with a small hobby razor, or even a small steak knife. It took 10 minutes on each with the file, or you might be ok carefully using a Dremel tool. (I've always found the Dremel allows you to make a bad situation worse, much more quickly.) I am seriously questioning my purchase, just to save a couple $$- It's not worth the time and frustration. It would be sooo easy for a new mechanic/rider (or an experienced one in a hurry) to cross-thread the hole and ruin the only water bottle mount.... I've used other ROCKBROS parts on my bikes and have always found them to be decent quality for the price. I just installed one of their bags on the rear rack of that same Lectric and the "Warranty Card" actually said that they would offer replacement within 15 DAYS of purchase or "free maintenance" within 30 DAYS of purchase. Everything else is in Chinese so I'm not sure if I'm required to mail the item back to them in China and I suspect that even the international phone call to find out would be much more $$ than the item was worth..... I can't help but think of the cosmic divide between ROCKBROS "Warranty" and what Lectric just did to fix the brake issue on the XP 3.0 Customer service wise I think that tells me everything I really need to know. Consider spending the couple extra $$ on your water bottle cages.........And DON"T CROSS-THREAD THE DARN THING!! -Hope this helps

Like the water bottle holder and easy to install, the quality as expected and its light weight, fit was nice and added new look to my bike, now I can take longer rides

This is a very sturdy bike water holder. Works really well, good fit on bike.

even though it is a Ultra light weight bottle cage, it is easily breakable and not of good quality

It doesn't fit a litre bottle. I have a 750ml thermos and that also struggles to get in. I feel it might snap while I am trying to house the bottle in. But other than that it is good. It is light and seems robust and once the bottle goes on, it seems quite secure. So no complaints. And after 2 months of use, I was wrong. It has not snapped. I now have the confidence to place a litre bottle also and it works just fine. So upgrading to 5 stars!

Quick delivery, look great and a good quality

I think it was a cheap plastic material and probably won't last? I wanted a larger bottle, it would be a tight fit while riding. This is just my opinion, it may work well for you?

Produto de muito boa qualidade