- Cheetah Tilt TV Mount fits 32-86 Inch TVs up to 165lbs Max VESA 600x400mm, with 10ft HDMI Cable, Universal Flat Wall Mount Bracket, fits 16-24" Studs, Ultra Low 1.3" Profile Adjusts to 15 Degree Tilt

I was skeptical of this mount. Why should this be so cheap compared to other mounting kits? I ordered one (due to the price), and prepared to return it if I did not think the mount could handle the weight of the 52" LCD TV (Samsung). Once I got it, I understood the cost. Good low-cost design and built with solid heavy duty steel. - Two horizontal bars are load-bearing, and for proper VESA spacing, they have to be parallel and relative distance must be in the right tolerances. These are made of solid steel. - Two vertical bars (in the wall mount) are flimsey, and that's ok. it should be solid enough make a rectangle box w/ square angles. That's it. - Two vertical mounting (to the TV) brackets are of heavy duty metal. Making this in to two parts (not one), reduction of material, but also allows free horizontal adjustment on the TV mount. - By doing the above, the kit is small, uses less metal (and reduce shipping and material waste). Positives --------- 1. Good solid and heavy duty construction. 2. Good value (low-cost). Paid less than $ 25 including shipping. 3. Easy install. Took 15 min to figure out the instruction (which is not totally clear), and 10~15 min to install and ready to watch. 4. built-in level worked well during marking of mouting holes on the wall --I tested w/ my own, and was consistent. 5. Once the mounted on the wall, and bracket on TV, you could adjust horizontal TV placement on the mount, just by sliding few inches left or right, post install. I expect this to be safe and true if the wall mount is directly screwed into the wall studs. I do not expect dry-wall install without the use of the studs to handle such adjustment. 6. The brackets on TV could also be used to adjust vertical TV placement by a few inches up and down. But for this one, you'll need to lift TV off the bracket and adjust and pull back :-). 7. There is a reasonable space (I would say, just right) from the wall to the TV to get cables/connectors through WITHOUT using any expensive 90 degree connectors. Plenty of space between two horizontal bars to put extra power outlet and data HDMI cable outlet to hide all the cables. 8. This supports tilt up/down, and works well. Amazon product description does not make it clear. Negatives --------- 1. Just one. Clearer instruction so that I do not need to spend 15 min figuring things out. One could learn a lot form IKEA :-). 2. Packing/Packaging -- Not necessarily Cheetah Mount issue -- mine came w/o missing parts, although I noticed torn cardboard box edges and some parts COULD have been lost during shipping. Either double box, or have Cheetah use heavier box stock. Helpful Hints & Comments ------------------------- 1. DO NOT forget to tighten the screws (2) on the bottom horizontal bars AFTER TV is placed on the wall mount -- especially if you are in CA w/ quake. This is what prevents TV falling off the mount accidentally. But do not over-tighten (you are NOT securing from left-to-right movement). 2. Very happy w/ my purchase. Will get one more for my other TV.

I purchased this wall mount in February 2018 to mount a 55" TCL 55S401 in my family room. The TCL is 55" and weighs around 35lbs. The VESA mount is a 200 X 200 VESA mount. While the Cheetah wall mount includes several different sets of screws to accommodate a variety of TVs, my TV needed a four M6 x 16MM screws. Cheetah included an M6 x 20MM set of screws. I dropped into the hardware store and picked up a set of 4 M6 X 16MM screws and washers for $3.40. Overall, I am very happy with this wall mount and I will buy another one when I get a TV for my office. I can easily recommend this TV mount. Based on other reviews, I was a little concerned and almost didn't order this wall mount. Some of these complaints need to be qualified and some of the complaints have been fixed by Cheetah. OTHER PEOPLE's COMPLAINTS: I had read previous reviews and the three points that have been raised by other reviewers were: 1. Poor or confusing instructions 2. Cheap or flimsy construction 3. Inability to hide the cables that pull to release the display 4. Once mounted, you can move the bottom of the TV on the mount (there is a little play) 5. You have to assemble parts to extend the mount to anything larger then 16" studs 6. Don't use the included level. It isn't accurate. For the low price and taking the complaints with some healthy skepticism, I went ahead and ordered this mount instead of just ordering a $100 mount. I was pleasantly surprised. It appears that the manufacturer has been paying attention to the feedback and has addressed several of the complaints and even included documentation pointing out the changes to the mount. I'm going to address each of the points listed above with my observations. COMPLAINT: 1. Poor or confusing instructions MY EXPERIENCE: If you have never put together a piece of furniture from ikea, yes, you may be confused by these instructions. If however, you have done any home repairs beyond replacing a light bulb, you will be able to figure this out without any confusion. For me, this was simple and easy. Maybe this is one of the things Cheetah fixed. COMPLAINT: 2. Cheap or flimsy construction MY EXPERIENCE: The metal construction of this mount is actually stronger then I expected. It appears as thought they have changed the design to use stronger parts. Yes, the hooks that you attach to the VESA mount on the TV and use to hang the TV on the bracket are not as robust as the metal on the wall bracket, but they are more then enough for the task at hand. I didn't experience them as being flimsy or at any risk of bending. The documentation did point out that they had included new stronger lag bolts, but still warned not to over tighten them. COMPLAINT: 3. Inability to hide the cables that pull to release the display MY EXPERIENCE: Cheetah now includes two magnets to stick onto the handles of the pull tabs so you can easily hide the pull tabs back up under the TV. COMPLAINT: 4. Once mounted, you can move the bottom of the TV on the mount (there is a little play) MY EXPERIENCE: Yes, this is true. Once the TV is mounted to the wall, you can press against the TV and there is a little play on the bottom of the TV. This doesn't really bother me. Once the TV is mounted on the wall, I don't actually go touch the TV. I use the remote control, so if there is a little room for play on the bottom of the mount, this doesn't actually affect the function or performance of the mount. This is just me. I am sure that just knowing that there is play in the mount will bug some people to no end. If you already know that something like this will bug you, this isn't the mont for you. COMPLAINT: 5. You have to assemble parts to extend the mount to anything larger then 16" studs MY EXPERIENCE: The mount has a small main rail that you can mount all by itself to the wall. This is 16" wide. If the studs in your wall are perfectly spaced so that the center point of the TV would fall exactly between these two studs, then you are all set. If like 95% of the rest of us, you are going to experience something less then the perfect situation, this mount is adaptable. It comes with extra rail sections you can attach to lengthen the wall mount. This allowed me to extend my wall mount and be less precise with how centered the wall mount was on the wall. I made sure the main 16" portion was where I was going to hang my TV and I used the extra extension to reach out to the next set of wall studs to make sure the wall mount was securely braced against the wall. The holes for the lag bots to score into the studs were oval shaped so that I even had flexibility to drill the hols i the studs and have some ability to adjust. COMPLAINT: 6. Don't use the included level. It isn't accurate. MY EXPERIENCE: I already own a very good level, so I didn't even check the included level. That being said, on my first attempt to hang the TV on the wall, I discovered that while my TV was perfectly level, my house was not. I live in an older victorian and the built in wainscoting and crown moulding were sloping towards the back of the house. Actually, I suspect the whole house slopes. So having the TV perfectly level was actually a bad idea. I took the TV off the wall and adjusted the hanging brackets by loosening the screws into the VESA mount points and moving the brackets on the left down a little. In fact, when you are first mounting the brackets to the back of your TV, you put the screws through long oval slots rather then a round hole. This gives you the freedom to adjust the brakes up or down by about an inch. I recommend mounting the brackets in the middle of the oval hole so that you have room to adjust up or down if you need to make some fine adjustments. MY ONLY COMPLAINTS: If you need to adjust the tilt of the TV or the leveling of the TV, you will need to take the TV off the wall and make the adjustments. I know that there are other mounts out there that make this a slightly easier process. You only need to make this adjustment once and then you are done. For me, I didn't see that convenience worth paying 4X the price of this mount. I know that this cost/value equation is different for everyone. For me, this wall mount is great and I will happily get another one when the time comes to hang another TV.

No se puede pedir más por este precio. Se fija un marco a la pared, los dos soportes de la TV a la parte posterior de la misma (los agujeros para los tornillos ya vienen de fábrica), vigilando de no apretar demasiado (¡¡no hace falta!!), ... y ya está el montaje. A continuación, conectamos TODOS los cables de la parte posterior de la TV (si hay alguno que pueda ir en un lateral mejor, ya que queda muy cerca de la pared y pueden quedar forzados) ANTES de colgar la TV para no tener que hacerlo dos veces y ya está. Un poco delicado el colgarlo: vienen dos ganchos por lado y hemos de asegurarnos de que cuelga de los dos de cada lado, ya que se mueven de manera independiente y puede quedar uno suelto). Según el tamaño de la TV y la altura a la que vaya situada puedes requerir ayuda. Luego apretamos un par de tornillos en la parte inferior para que quede fija, tras elegir la inclinación que nos gusta, y ya está. Sólo lleva un par de días colgada, por lo que no puedo asegurar cuánto aguantará, pero dado el tamaño de los tacos y los tornillos de la pared (incluidos), creo que aguantará sin problemas. El servicio de entrega fenomenal, un día antes de lo previsto. De regalo vienen unos niveles, un cable HDMI que parece de buena calidad, una gamuzita, una linterna LED pequeñita,... y todos los tornillos, arandelas, etc. que no vayas a usar. Lo dicho, viene todo lo necesario y más.

Good wall mount for the money. Fairly easy to install, but issue was with the extension brackets. It took me a couple of minutes to get them lined up properly, but after that it was good. My worry is, with the extensions on, I wasn't sure if the the extensions could hold the weight of the TV with the lag screws off-set fairly severely; but, so far, so good. It seems solid enough and works well. The bonus HDMI cable is nice! Update: WOW! The customer service is AWESOME. Their response to my (I thought) fairly positive review has been overwhelming - so much so, that I've updated my rating from 4 to 5 stars. To date, the mount has held up VERY well, with absolutely no signs of the any part of the mount sagging, even with a lot of weight on the extension. Very sturdy and yes, I'd recommend this mount!

Ho comprato questo supporto attratto dal prezzo e dalle tante e buone recensioni, specie di quelle che hanno evidenziato ottimo supporto del venditore. All'arrivo, velocissimo come nello stile Amazon Prime, ti trovi di fronte a un imballo ben curato con all'interno a 4 staffette imbustate, leggere, ma al tatto di buona fattura. Le staffe a Muro, vanno assemblate in modo semplice, ma nel mio caso ho dovuto forzare leggermente gli incastri per allinearli. Assolutamente nulla di grave. Mi sono accorto subuto che i tasselli inclusi, non sono di primissima qualità. Ce ne sono 2 da 10 per il lato superiore e 2 da 8 per il lato inferiore. Senza perder tempo li ho sostituiti con 4 FISHER da 10 e sto tranquillo, anche perchè ci ho appeso una Sony Bravia del 2008 da 40" da circa 25kg. Nella confezione è inclusa anche una piccola livella magnetica, ma mi sono accorto che non era molto affidabile, non tanto per la funzionalità in se (alla fine è una bolla di aria) quanto per la costruzione della stessa non proprio dritta e con la banda magnetica che si spostava facilmente. Ho utilizzato una mia livella per evitare problemi ed anche qui il gioco è fatto. A prescindere da questi piccoli accorgimenti, una volta messa su la TV, la stabilità è perfetta. Non si sposta di 1mm. Un'altra nota positiva, sono i tiranti che permettono lo sgancio inferiore in modo immediato. Avevo dimenticato di passare un cavo HDMI e l'ho sganciata e riagganciata in un secondo. Incluso nella confezione il cavo HDMI... ma che onestamente non ho utilizzato poichè non mi sembra un gran bel cavo, ed un paio di gadget, che ad onor del vero ho cestinato poichè inutili. Ecco magari avrei eliminato tutti e 3 i gadget a favore di una livella magnetica di qualità migliore. Ad ogni modo, soddisfatto dell'acquisto e consigliato.

Había dos productos muy parecidos, de la misma marca pero distinto precio, son el modelo APTMLB y el APTMM2B. Compré los dos y he de decir que son muy parecidos, pero el primero tiene unos huecos de hasta 800x 400 y puede funcionar para TV's de hasta 75", y el segundo tiene unos huecos de más pequeños de hasta 684 x 400 y puede funcionar para TV de hasta 75" también, siempre y cuando su TV esté dentro del peso y tamaño sugerido. Ambos soportes de todas formas son bastante económicos si los comparamos con otros del mercado, y hacen su papel. Conviene tener en cuenta que son para teles grandes, y que si se quieren usar por ejemplo para una tele de 32 o de 40 pulgadas sólo hay que poner la mitad de las piezas. Luego viene con dos niveles de burbujas muy útiles y con un cable hdmi, alguien da más?

Ho acquistato questo supporto per una smart TV da 43 pollici. Devo dire che si tratta di un prodotto davvero buono, molto solido e resistente. Sono rimasto sorpreso perché ad un prezzo piuttosto contenuto viene fornito anche un cavo HDMI (molto lungo e comodo) e addirittura una livella per facilitare il montaggio. Non do 5 stelle solo perché il montaggio è reso leggermente complicato a causa della mancanza di istruzioni in italiano, ma con un po' di pazienza ce la si fa comunque. Aggiornamento: il produttore mi ha rimborsato la metà del prezzo del prodotto in risposta alla mia lamentela circa la mancanza delle istruzioni in italiano. Che dire, non mi era mai capitata una cosa del genere e sono rimasto davvero (piacevolmente) sorpreso. Credo che questa gentilezza ed attenzione per il cliente meriti 5 stelle.