PGN UCP205-16 Pillow Block Bearing - Pack of 2 Mounted Chrome Steel Bearings with 1" Bore - Self Alignment

Good bearings. These saved my team because the other alternatives were super expensive but this was very affordable and did the job.

I got these a to replace the cheap pillow bearings that wear out every other year on my swamp/evaporative cooler. They were wide enough to fit on the rail in my mastercool (1.5" wide), and a drill bit away from having new bolt holes. It made the squirrel cage about 1/4" higher, but no issues with airflow from that. My cooler only spins at a max of 2100rpms which is far below the max these are rated at. All that I added were the M10 bolts and nylock nuts. I'll update this review over time and if anything changes. For my cooler upgrade application: Pros: - 2 grub set screws per bearing - Pre aligned bores - grease zerk with protective caps (will see how long those last) - Sealed pillow bearings on each side so the grease doesn't just fling out - Nicely machined 1" bore - Pre greased Cons: - No additional hardware Other: - Because I was using these in a very different application, not surprised bolt holes didn't line up with old cheap swamp cooler pillow bearings. So this means you'll need to drill some holes in your rail to make it fit with proper bolts.

Good little pillar blocks for the price.

I purchased a two pack of these pillow block bearings for a flat sander project that I had just finish designing and I am now in the process of building. I am always amazed at these bearings and how well they work and how cost-effective they are I have mounted up my large 22" long contact Drum between two of these bearings and they run smooth as silk. The bearings seem to be very well built and are double sealed and should hold up well in this application I have used similar bearings from this company before and they have lasted a long time. I highly recommend these bearings and would use them again. Thank you

I used these for a DIY pottery wheel, as part of a pulley gear reduction. We used a small section of aluminum rod for the axle, which worked great until I had to take the axle out to adjust the pulleys. Turned out I over-tightened the set screws, which deformed the aluminum enough to get it completely stuck. After much wacking with a hammer/wood block, I eventually just sanded down the deformed part of the axle enough to get it unstuck, but there was a lot of forces on these bearing blocks in all sorts of directions. Despite this, they still spin fine and remain just as quiet as before. Absolutely a good buy, and I'll keep this brand in mind next time I need something similar.

GREAT and 1/3 the price IT WAS 169 $ EACH at the bearing place install and working great THANK-YOU

PGN - UCP206-20 Pillow Block Mounted Ball Bearing - 1-1/4" Bore Review edit 07/07/2021 I have used several of these BRG's and have had on problems with miss alignment, I have read other reviews that state the brg,s are out of alignment, These are self aligning bearings if the are not able to self align I would check and see, That if it's not a manufacture problem on the bearing but on the final users design as far as the alignment goes, there's a lot of room for the final assembly to be corrected buy the bearings ! Great Bearing's, Excellent price, I used these 1-1/4" bearings to attach 2 - 7 foot gates to the framing of my shop to keep my explorer dog from exploring. ( also keeps his furry friend's out ! I used 1" ID. Black Iron pipe for the shafts, turned down to 1-1/4" OD, works great, but a little over kill on the bearing size so when I built the gate for the 12 foot door on the other side of the shop I used PGN - UCP205-16 Pillow Block Mounted Ball Bearing - 1" Bore with 3/4" ID. pipe Turned down to 1" OD. The gate sections are fence sections that I purchased from HFT many years ago work great for larger dog's, maybe not so good for smaller and pups.. I have just reordered a additional set of the 1-1/4 in to make a 16X4ft automatic swing gate for my driveway. (Will write a review on how that turns out shortly !!)

Nice and solid bearing seems to have nice preload. Will be using it on a diy wood lathe. Bought .625 bearings. I have a ground rod that’s exactly .625 and the fit is a nice sliding fit. So bearing must be ground over size by about .0005-.0015. Initially I was dismayed as my bar didn’t fit but there was a slight burr on my bar where it was cut. Took the burr off and it slid right in. I will definitely be using pgn products again. Very mind blown with how good this purchase was. Some people said in comments that bearing was shipped as metric to them. This did not happen to me, so it may have been a mistake in the past.

Projet futur

fonctionne très bien, bien contente pour mon achat

The quality looks good for cheap bearings

installed on a vibratory tumbler. still doing what bearing do. good part. would buy again.

Arrived on time and in good condition. Top line quality here. They even have grease fittings so they should last a long time.