Nilight Front Bumper Compatible for 2007 2008 2009 2010 2011 2012 2013 2014 2015 2016 2017 2018 Jeep Wrangler JK/JKU Rock Crawler Fog Lights Hole Winch Plate

Bought this to replace the factory bumper for my 2009 JK UNLIMITED Rubicon it was all faded and looked goofy with the Barricade slim fenders I have. The install took about 2 hours (Arizona Heat) lol. It’s a 1 person job because the new bumper isn’t that heavy. It is kind of frustrating mounting the fog lights to the brackets you have to hold the nut on the backside of the bracket to screw them in at fat fingers and tight spaces don’t go together. But in did manage to get them mounted. The other thing is the bolts that are in the bumper there are 3 on each side then you have 1 bolt on each side you screw into the bumper had a little bit of trouble lining up the holes but eventually I got all 8 bolts tighten down. Overall not a bad install. I would recommend this bumper for the ease of the install and the looks.

This is a great sturdy bumper. Lots of room behind to run wires or whatever and keep it protected. I am impressed. Only had it a short time but well laid out. OEM Fog lights was a nice touch! Mounted 12k Badlands Winch easily and the front camera was easy to install as well. I like how it is not "In your face" but very functional for off road. Install was super easy. Find the bolts to remove the old bumper after removing the connection to the Fog Lights, move the fog lights to the new bumper, mount it up, and done! Fog Light wires fit, however, just barely. Had a bit of work to do there, but 10 minutes maybe. Total install, taking my time, two hours. One thing I upgraded was the D-Rings, these in the pic are the galvanized ones that came with it and I upgraded to some black ones. I really like that look a lot better! The Winch was easy to mount and route the wires. Did take a bit of time to decide where I wanted the on/off switch, but decided to put it under the hood by the battery. Works well! I had a License Plate bracket that took two self tapping screws to install. When I go off-roading, I will be able to easily take it off so it does not get damaged. (Don't remember where I got it, but any of them will do). The front camera (hard to see) mounted nicely above the License Plate but below the winch where it will not be in the way. Note, did have my German Sheppard supervising the whole time... She likes it as well!

This is my second aftermarket bumper . I chose this one primarily because it accepts the factory fog lights and the finish looked thick and textured in the pictures. It delivered quickly by fedex ground. Because the bumper is so heavy it did break through the cardboard box. the last bumper I bought was packed better. That being said the heavy coating kept the edge from being damaged. I was not surprised to find out that the factory hardware did not work to install the fog lights. I have not decided how to remedy this yet. I was surprised to find out that the factory wiring harness did not reach the openings in the new bumper. I have ordered wiring extensions ( $20 on amazon ) rather that cut and extend the wires myself. As far as physically installing the bumper it went right on. The bolts lined up nicely , which did not happen on the last bumper I bought. I chose to keep the plastic pice that fils the gap between the bumper and grill. I wishI could have reinstalled the plastic pan that goes below the bumper but there was no way to attach the front of it. The bumper looks great and is really heavy duty so I expect great durability. I would recommend this bumper , just plan ahead for challenges installing the fog lights.

Just finished with the installation of the bumper & winch. The winch was not purchased through Amazon. A little about my Jeep. 2008 JKU. 2.5 inch lift. Was looking for a bumper to add a winch. Review: Packaged nicely. No issues with the product out of the box. As others wrote, holes lined up great for bumper, fog lights, and winch. I bought the fog light extension wires. Even though some noted they were not needed, I felt it made the install easier. I was able to salvage the plastic undercarriage, too! Rears connected to stock holes. I used zip ties for the front. Winch installed easily, with the winch and fairlead holes lining up perfect. Install Tips: I'm in my 60's and was able to do this in the garage by myself. Whole thing took me 3 hours. Could've cut down an hour if there was more room to get the nuts on the bolts for the fog lights. That was a bear! You have to be ambidextrous to get the fog lights installed. You'll need a 2.5 m allen and 8m box wrench to hold the nut on a couple of them. Others, you need long fingers and lots of patience. Swivel head ratchet with extensions and deep sockets, helps with the bolts and nuts for mounting to the bumper. Lastly, I broke 10 drill bits drilling 2 holes for the license plate. It would've made a world of difference if they'd have those pre-drilled. Overall, happy with the purchase, install and product. Would recommend to other early JK owners.

Great fit. My husband put it on himself and it looks great. He has a 2013 Jeep Wrangler, great fit, matches the color well. Easy to put on had all the parts and instructions. Great buy our winch fits well also.

Easy install, installed by myself. First off, when the bumper arrived the box and packaging were great, no damage to the box and good amount of styrofoam inside for protection. Hardest part was removing the stock bumper. Like other reviewers no included hardware to mount the factory fog lights, not too bad had some screws that fit everything lined up and fit great. You can use the factory fog light wiring without having to buy anything else, you just need to cut open the wire cover and pull out some of the slack and it reaches no problem. Looks great and good value.

I love it my jeep 2015 jk looks waaaay better

I like the design and the weight of the bumper. The powder coat was broken on a few locations, the fog lights can not be mounted with the OEM screws, and the fog lights can harness would not reach both lights, required adding 6 inches of extension wire to one connection. The last problem was the hardest to overcome the bolt pattern would not line up, had to twist the bumper on open side to get the alignment. Seemed like a heat warp of the bumper from the welds. It is mounted so I will not return it. Hope when I get a winch that at least will go better.

Solides et durables Dit parfaitement sur un jl 4xe 2022

Very happy with bumper fit great and all proper hardware was provided great product

Ordered, given ship date, that came and went so weeks after I tried to cancel and as soon as I did I was told now it’s being shipped. By the time it arrived I had bought another one for sane price and it was much heavier and sturdier than the nilight so I returned it.