(2-Pack) AR-PRO 15x6.00-6" Inner Tubes with TR-13 Straight Valve Stem - Replacement Lawn Mower Tire Tubes with TR13 Straight Valve Stem - Suitable for Yard Tractors, Wheelbarrows, ATVs, and More

Had a flat on my mower trailer. The tube ripped at the stem. Got the new tube, took about 3 minutes to install the new tube. It is holding great. Good quality, and now i have a spare should the other side go out. Would recommend.

Worked good. Held air

The product arrived quickly and as expected. Overall quality seem good. The valve stem is offset from the center, as in the picture I appreciate that! I did struggle quite a bit replacing this tube. I do not feel it was any issue with this product, moreover, an issue with the quality of the rim. I overloaded my original tire and had to draw horizontally and it poped this also caused significant damage to the rim. I repaired the rim and when this tube arrived I struggled installing it. The valve stem pulled in when seating tire bead, againwhen filling. I ended up using a flat washer and a wire tie to keep it in place. ( I would highly recommend this). This was no fault of the tube or the product more an issue with my rim. I have replaced many tires, tubes and all sorts of vehicles, cars, trailers, atvs, BMX. I struggle with this replacement due to the rim and tire. I did make this repair and able to use the dump cart, but also ordered, a no flat wheel assembly, to install later. Overall this product performaned as it should, and would recommend, but only if you have a quality rim!

The size I bought is 20 x 8.00/10.00 I only gave these 4 stars because I haven't had them on the rims long enough to write about durability. I may come back later to update this review. The tubes I received are MUCH thicker rubber than those I have gotten before, and I was not expecting that in this price range (2/$30.00) I'm not complaining, as I often get thorn punctures, and then have to add liquid tube sealant-maybe these will better resist punctures. These also have the full length threaded metal stem with washer and nut retention-which I was looking for to better protect against rim cutting of the stems when/if a tire loses a lot of air and the tire gets loose enough to begin to push the tube around. I try to use tubes in any lawn and garden wheels originally equipped with tubeless rims, and I have to say that these, being thicker, were tougher to install. I ended up using talcum powder inside the tire and on the tube-something I have not had to do with these smaller diameter units. A couple tips tip to anyone out there who hasn't installed one of these smaller diameter tubes and/or tires before and wants to try it. Once the tire is off the rim completely or on one side (for installing a tube) take a good look at he inner surface of the rim. If the rim shows any sign of serious rust inside, do yourself a BIG favor, take the tire off and sand the rust smooth and AT LEAST spray it with primer, or the rust-(which will continue to grow), has a good chance of puncturing the tube eventually-or rusting through the rim. There may also be some very sharp factory artifacts from welding-(they often let things like this pass inspection if a rim is destined for use with tubeless tires). A rusting rim often makes a pinhole, or raises a tire bead just enough to cause an air leak-or can abrade a valve stem. If you don't have the proper tools to break a tire loose from the rim and install a new one-get them. Its very easy to directly damage a rim (or a tire OR A tube) by using substitute tools that have sharp edges-and also by raising burrs that may snag the tube you are going to install. Speaking of tubes, there is an inexpensive tool that screws onto to the end of the tube's valve stem to help thread it through the rim hole-(something that is much harder to do with big hands. big fingers and tiny tires and tubes). If you don't have one of those you can sometimes substitute a valve stem extender to make it easier to find and steer the valve towards the rim hole.

Great inner tubes at a great price.

Fit and worked as it should and good price

The original tube had a tear inside the wheel by the valve stem. This tube was easy to install and holds air better than the old one. Th tractor sits about an inch higher and gives me a better cut since replacing the tube.

I bought these to permanently fix my riding mower tires. I have become completely tired of putting air into the front tires of my riding mower. I've been putting off the task of putting tubes in my riding power's front tires for 4 years. I finally decided to take the plunge and do it this year. These tubes fit perfectly and I can finally get on it and mower without having to grab my cordless inflator as I head out the door. This is well worth the investment. UPDATE 5/16/26: I unpacked the tubes and CAREFULLY placed them in the tires using BLOUNT TIRE SPOONS and proceeded to inflate. The first one functioned as expected but the second one would not inflate over 3 PSI. I CAREFULLY removed the tire using the same tire SPOONS to investigate the problem. I then CAREFULLY removed the tube making sure AGAIN that there were no sharp edges or obstructions. After attempting to inflate, I find 2 small slits in the side of the tube. These could not have been caused by improper installation. I attempted to apply a patch, allowing the glue to cure for 18 hours, but that did not fix the problem. I deducted one star because I failed to pre-inflate prior to installation for inspection purposes. The quality of the rubber is questionable. It seems to be much thinner than most others I have used recently. Buyer beware.

works as should.

My Cub Cadet zero turn front tyre kept coming off the rim. So put this tyre in it and boom! Fixed. Thank you.

Buena relación calidad precio.

I used these on a pair of 24x12R12 tractor tires and they worked just fine. The valve stem was offset a bit which worked well for the rims. Like any tube bigger than a bicycle tire they can be tricky to get in and lined up, but they did what I needed.

Vraiment bonne