Tyger Auto T1 Soft Roll-up Truck Bed Tonneau Cover Compatible with 2016-2023 Toyota Tacoma | 5' (60") Bed | TG-BC1T9044

I'm really pleased with the results on this! I like that the surface is taut and the edges come out nice and even (see photos). There's some room for interpretation on how far back to set it from the cab. I decided to leave a small gap so any frame flex won't cause it to rub on the cab's paint (see photo). It took a little thinking before I was confident on how to best install the foam seals despite the drawings in the instructions, but I worked it out. I include a photo of how the seals installed before putting the cover on to hopefully help others see how it worked for me. On my 2025, it turned out the slightly thicker seal they provided for the 2024 was a better fit (the box had both). After installation, I could see very small slit of daylight between the gap and the cover in the outer corner when looking from inside with the cover closed, so I used the second seal they provided to block that from the inside while laying in the bed with the cover closed to see where any light peeked through. It would probably have been fine regardless. The minor wrinkles in the vinyl cover from shipping disappeared after sitting out in the sun a couple of hours. The crossbars that create a slight dome both side-to-side and front-to-rear are nice and will help keep it tight and free of pooled water. The latches are straightforward; they engage and release easily. The clamps holding the side rail appear to be nice and robust. It's easy to roll and the straps that hold the roll at the front are easy to use. My final installation recommendation is just to take your time at each step and make sure both sides of the rails are symmetrical. The decorative factory markings in the plastic on top of the bed sides make it easy to compare the placement on each side. To get the tightest fit when closing: First unroll the cover completely, then while standing at the back disengage any Velcro that has attached along the sides by pulling the cover fairly high up and then back and down to the engagement pivots, then pivot it down and latch. After it is latched then check that the velcro at the sides is fully pressed down.

​I bought this for my 2022 Tacoma and the description was 100% accurate. It only took me about 40 minutes to install and the instructions were very easy to follow. It fits perfectly and looks "super nice" on the truck. Great quality for the price.

Easy to install... for the price pretty darn good.

Just installed this on my 2025 Tacoma 6’ bed. Installation went smoothly (xtra thick head rail seal was required to seal completely) Once installed fits well & looks great. Great value for full access to bed , & keep your gear dry.

Great topper easy to assemble. Fit was perfect with minimum leak. Latches tight but Velcro needs to be reset after removal

Great bed cover. Seems well made, install was easy, and it's a perfect fit for my Tacoma. Seems to be designed better than my previous cover, which was Truxedo brand.

Update: 11.28.23 - Cover shows no significant signs of wear. No cracks or tears, and still steches taught. I keep it clean, and still wipe it down every other month with whatever vinyl protector I have at the time. The cross bar closest to the tailgate does stick sometimes, but nothing a good bop doesn't fix. 38k miles on it. Update: 11.07.22 - Cover is still performing as needed. I did lose the little rubber emblem on the back edge, and I have had to "tighten" it up once, but it is still performing as new. I wash it when I wash my truck, and wipe it down with whatever protectant spray I have lying around. 3 Florida summers and 20k miles including two 1k mile road trips, no issues. Update: 10.11.21 - still going strong. No fading with 100% exposure outside in Florida. I do make sure I wash it when I wash my truck and spray UV protected on it though. All seals are good and while still not 100% waterproof it keeps the majority of the things dry in my truck bed. /Update Relatively inexpensive, easy to install, and makes the bed water resistant. I chose the soft roll up because with it, I still retain the use of my full bed (which is already small to begin with). If I need to haul an over sized item (washer or other appliance), I can roll the top up and push the item all the way back in the bed. Trifolds won't let you do that, you'll always have at least a third of your bed covered, or can't see out the back window. In terms of weather(rain) resistance, it keeps enough of the water out. It is by no means water proof, but I'd say it keeps the bed dry enough for me not to worry about what's back there. I live in Florida, and it keeps the driving rain we get out of the bed pretty well. Speaking of Florida, it's held up to the sun fairly well, so far (3 months of 100% outdoor exposure). If I can get 2-3 years without it cracking or splitting, I'll be happy. Function wise, it latches strong. Locks will only keep honest men honest, but I do not worry about what's in the back. I would GLADLY purchase another should I need to.

Great price! Super simple to install

Perfect fit, very high quality, 45 minutes to install on Tacoma 2016 long bed. 2 day delivery. Very sturdy hardware, aluminum, will not rust. Too bad I can't put 6 stars.

La verdad me ha funcionado muy bien, y no fue difícil de instalar, obviamente es de las versiones mas económicas de tapas para caja (bed cover) pero por lo que pague me ha dado buen servicio.

Drove to highway speeds, held snow good, very useful and easy to remove when you need to access the full bed.

got this for my 07 tacoma 6f bed and very pleased with my purchase. fits perfectly in length and width, took only about 1hr to install after watching a couple videos, and even worked with the bed rail system in place, thanks to the modified clamps that came with the package. looks good, and very affordable. only thing was the top half of the clamp was too "tall", so to speak, and I had to trim it down a bit in order to properly tighten the clamps onto my bed rail. this only added 10 mins to the install, having a grinder and a file on hand. small detail though. very happy overall.

(Tacoma 05 boite courte 5') Je suis très satisfait. Cest facile à installer . On jurerait que c'est d'origine ! J'ai meulé légerement une clamp pour que ca serre bien .