2mm / 3mm x 50M LCD Screen Repair Tape Cell Phone Adhesive Tape Thin Double Sided Tape Adhesive with 1 Tweezers for Cell Phone, iPad, Tablets, Laptops, Camera, LCD Screen Repair

I used the Kaisiking 2mm LCD Repair Tape while replacing the battery on my Samsung S10, and it performed extremely well. The tape has a strong, reliable hold, but what stood out most was how easy it was to work with. It cuts cleanly without stretching or gumming up the scissors, and the backing peels off smoothly, which isn’t always the case with ultra‑thin repair tapes. The included tweezers were surprisingly helpful—they made it simple to place the tape exactly where I needed it, especially in tight spots around the frame. Once applied, the adhesive held firmly without any mess or residue. For anyone doing screen, battery, or small electronics repairs, this tape is a solid, affordable choice that makes the job easier and more precise.

The Kaisiking 2mm LCD Repair Tape is a reliable adhesive solution designed for precision screen repairs on smartphones, tablets, iPads, laptops, and even cameras. It comes with a handy pair of tweezers, which makes handling the ultra-thin tape much easier during delicate installations. The 2mm width is ideal for securing LCD screens without bleeding over sensitive components, offering a firm and long-lasting hold without leaving residue. It’s especially useful for professionals and DIYers looking to reattach or reseal screens after replacing batteries or internal components. The adhesive strength is solid—strong enough to keep screens in place but not so aggressive that it damages parts when removed. While it doesn’t offer water resistance or heat shielding, it performs exceptionally well for its intended use and is a must-have in any repair toolkit. Overall, the Kaisiking tape is an affordable, effective, and user-friendly option for electronics repair, especially for mobile devices where precision matters most.

I used it on my son's iPad Mini 4. I replaced the battery a while back, and I just re-used the existing tape/goo to hold the screen on. A small gap formed over time, and a little light was leaking out. Using the existing tape and goo was a bad idea. I got this tape (the 2mm size) and re-stuck his screen a week ago. It's held up perfectly. Removing the old goo was a chore. I used a combination of isopropyl alcohol, acetone (nail polish remover), and Goo Gone (the citrus power original version), and a single-edge razor blade. I know most of the rest of this is more about how to remove goo from and ipad than about the product itself, but since this is a use-case for it, I'll elaborate on what worked for me. I also want to mention that I didn't have a single-edge razor blade starting out and was using an X-Acto knife. The single edge razor blade worked much better. Also I think the Goo Gone or something like it is really necessary. I think isopropyl alcohol and acetone aren't enough. 1. Peeled off as much of the old black tape/goo stuff as I could from the screen and chassis sides using my fingernails. All my tape was on the back of the screen, and the chassis side had only goo. The tape on the back of the screen sort of looked like it could be something other than tape that was there only for holding the screen down. It was all old tape for holding the screen down, and I removed all of it. 2. scraped off as much goo as I could from the chassis side using the razor blade. 3. I cleaned the chassis the rest of the way with only alcohol. I guess you could use Goo Gone on it but I didn't. The razor blade worked well enough that I needed only alcohol. 4. On the screen side, which had a lot more goo on it, I used the Goo Gone with both q-tips and paper towels. I scraped some of the goo off with the razor blade, but then I realized the back-side edges of the screen were painted, and I stopped using the razor after I took some paint off. This turned out to not be that big of a deal, but it could have been worse if I had scratched more paint off. 5. Cleaned off the Goo Gone using acetone. Then cleaned everything again with alcohol. Not sure if only alcohol would have cleaned off the Goo Gone well enough. I had acetone, so I used it. 6. Cut lengths of tape to fit the four sides of the iPad. I didn't bother with the rounded corners. I cut one, stuck it down, cut another, stuck it down, etc. (didn't cut them all at once and then stick in other words). The razor blade cut the tape easily. The tape has one side sticky and the other isn't sticky until you peel the backing off. Place the sticky side around the edges of the chassis side in the little groove. 7. Peel off the backings. 8. Re-attach the cables and screws. At this point I turned the iPad on to make sure it worked before turning it off and closing it up. 9. Pressed the the screen down. I went around the edges pushing down hard with my fingers. 10. Then I put the ipad on a table, screen facing up, and gently placed a six-pack of 12 oz soda cans on the screen. The six-pack fit perfectly, pushing only on the screen and pushing it into the chassis. I placed a few books on top of the six pack. 11. Left it like that for 2.5 hours. I did not apply any heat. Then I gave my son his ipad back. So far it's been fine (did this over a week ago). I hope it holds up. I think this is good tape for this purpose, and as I said, the 2mm size is perfect for the iPad Mini 4.

This is a black, double-sided tape that reminds me of two sided electrical tape in terms of being stretchy and sticky. I saw this specific tape recommended as a replacement for the adhesive strips inside some removable cases for foldable phones (e.g., Galaxy Z Fold 6), but I should have questioned that before purchasing. I'm going to advise anyone else against that. The good - the tape is very sticky. The little tweezers that come with it are useful. If you're using this to permanently repair something, it should do the trick. The bad - the tape is very soft/gummy/tacky. So once two things are stuck together with it, getting them back apart is a gooey mess. I can't recommend this as any kind of temporary adhesive, or for attaching things to the outside of a device that you want to keep clean. 4 stars, because I bet it works well in specific use cases; just be aware it's messy.

So far so good. Not easy to use, but easy enough. Very good stickiness. I would recommend 1.5mm for the I phone 14. I used 2mm. Had to trim it down in 2 spots to get a good fit.

Excellent quality tape and always nice to have extra tweezers.

This stuff actually works!!! My zflip 5 took a hard fall one day at work and landed on a concrete floor. It was open when it fell and it landed perfectly on it's back which is the side the mini screen is on. Long story short..... No glass was shattered or anything. Visually I thought I was good to go. Several days later my outer screen fell off only attached (dangling) by wires. I ordered this stuff and I was skeptical at first. But..... Nope! I'm 100% satisfied with this product. I just peeled a little back and worked it down one side at a time clipping it at the edge of every side before starting a new side. So I had basically 4 separate pieces stuck inside the edge of the phone. I carefully placed the screen on top ,applied some pressure around the edges, literally rubbed off any excess tape protruding from the outside corners and Bam!!!!!! Mission accomplished!!!!! No need for a new phone and no need to take it and pay to have it fixed. I highly recommend using this on similar projects!!!!! By the way I used the 2MM tape. One more thing.... those tweasers it came with were a life saver!!!! Hope this review is helpful for someone.

It wasnt able to hold the screen of imac 27" and it fell after 2 days. Maybe i didnt install it right but i am not willing to give it another try

Did what it should

Items work well as a adhesive.

セットのピンセットが広告の物と違っていたので速! 返品しました……で同じ広告の物が他の店舗から出ていたので買い直して…⁉️広告通りの物が来るかどうか？

Llego en tiempo, muy bien empaquetada y es de muy buena calidad.

Good adhesiveness for lcd holdup. Added tools helps alot