LAMPHUS Light Bar Mount Clamp Bracket for ATV UTV 0.75-1.25in Horizontal

picked these up to mount some auxiliary lights on my motorcycle crash bars and they are holding up great after a bunch of miles on rough roads with zero movement. the adjustable rubber inserts are a nice touch since you can get a secure fit on different diameter tubes without needing a completely separate product. lightweight aluminum construction and they have not slipped or shifted at all which is exactly what you want for something going on a moving vehicle.

I used this to make a side table to attach on the bar of my day bed. It worked perfectly! I like that the hole sizes are adjustable and come with different sized rubber rings to properly fit the bar its attaching on. I had to keep sizing up on the rubber ring to get it to fit! It was a tight squeeze and needed a lot of effort to get the screws to screws but it works and fits! If you put some weight onto the side table it does slip down, so just something to be aware of. But it was exactly what I was looking for and holds my drinks and food perfectly.

Look... I understand that these mounts were designed to be mounting brackets for ATV's and such. I'm sure they would do a GREAT job at that, they're very well made. But.. did you also know that these work great at holding outdoor curtains from sliding around in the wind?!? Crazy right? I imagine if your ATV or UTV had curtains this product would blow minds, but alas.. here I am telling you about the incredible multi-purpose aspects of these mounts because I have entirely too much time on my hands. Safe driving/travels (and/or homemaking)!!

... still a great way to install lights to a tubular bar.... I'd bought these to use on the front bar of the roof-cargo basket on my Forester. However, the clamps (and assorted rubber fittings) would not fit - either too small or too big. The aluminum brackets are a good size and look sturdy enough for most uses. But (again) the rubber fittings are either too small or too big to fit. Yes, there are another set of these brackets available (with a different set of rubber fittings) but they may be a bad fit, too. I was able to install them - solidly - on the rear bar. I can use them for some rear lights, once I figure out the wiring routes. The clamps are solid and the included allen-head screws seem solid and sturdy with the locking washers. NOTE TO MFG - you should include a spare set of locking washers - just in case. Given that they are small, and you're trying to hold the clamp together on a round bar, plus insert the bolt and ... well, it's easy to drop a washer and almost never find it. Verdict - for a limited number of fitments (bar diameter) this is a great item and seems well made. Without doing the math, it may be difficult to find the right size for the diameter of your mounting point. And the price? Can't beat it.

Sturdy better than expected but I will put in better screws later mount is great itself

Works great as a mount for my Chinese tire pressure monitor also bought on Amazon. The old mount had broken and I bought this. The hole for mounting is one centimeter wide and too big for the screws I had to use. I found a one inch self-centering screw for the hole and used a T nut on the other side to center it and lock the bolt into place. Mounted the tpms. Easy! Attaching this mount to bars is simple. Just find the included right size rubber pads for your bar, place them in the mount, place the mount on the bar, and attach the screws. Tightened down, this thing will not move. Happy with my choice. The only brand I could find offering a single mount. Can't beat it.

The product is nice looking, light weight, fits a multitude of bars, but my main issue is how easily the screws holding the two pieces together strip out when under minimal pressure. I tightened it down by alternating between the two screws until it was getting snug, and I tightened the bottom screw up until I thought it would hold tight without issue. After a 3/4 twist on the top screw (the longer piece of aluminum), it got tight and then stripped out rendering the piece useless. It was weird how the top piece stripped out with less pressure than on the bottom piece. The other bracket went in without issue. Well, I have to say customer service and getting a refund was a piece of cake. I sent an email to the vendor either on a Friday night or Saturday morning telling them I needed half of a new piece, and much to my surprise, I received an email on that Saturday. They stated they couldn’t ship out a new one due to the Coronavirus lockdown, but that they would refund my money and I could order a new one. My refund came immediately and I turned around and ordered a new set. While installing the new one I decided I needed to make a change to the other bracket that originally installed without issue. When I went to tighten it up again, the top screw on that set stripped out. Again, I did not tighten too much, it is just a lousy design to use such small screw threads on a piece of aluminum. Thankfully, when they sent me a new set, it was a pair so I still had an extra bracket (so much for using it on my kids quad for a spotlight). I don’t know why they can’t make this with a bigger screw or coarser thread so that it doesn’t strip so easily. I ended up using blue loctite on all the screws, but I was hesitant to tighten that last bracket down too much and I’m hoping it doesn’t move on me from vibration. I’d probably rate this item lower, but due to the excellent customer service and their willingness to back their product, I gave it a 3 star. The company itself gets 5 stars, they were great!

I was searching for a suitable mount for Deanli Soundbomb horn to my Rocket 3 and stumbled upon this. I couldn't be happier with it. It's solidly built and still light weight. I had to put it together and take out several times to locate a suitable position on the bike for the horn. It still kept it shape at the holes and where the screw went in, tightened and came out several times. The included rubber teeth set is also of good quality. They grip well and do not destroy the paint. The Denali horn I mounted feels like more than 1 to 1.5 pound heavy. But this mount is still holding it well after several miles of ride on bumpy roads. For the price or otherwise, this is an outstanding selection. BTW, I had to reach out to he customer care and their services was excellent. Looked like they are based out of California. Highly recommended.

Ideal for mounting extra lights to my motorcycle crash bar. Enough fitment options to fit a variety of size tubes.

Well made mounting brackets.

Firstly received the package and quality is extremely good. Ordered four sets however all were lacking full package contents meaning they were useless for my purpose and now I have wasted my valuable time arranging a return to Amazon (who have been extremely professional in sorting out the issue). The following lists the items and details what was/was not in the package. 2 x Mini Bar Clamp ~ YES 2 x Rubber Strip ~ NO 2 x .75" Rubber Insert ~ NO 2 × 1" Rubber Insert ~ YES 2 × Hex Key ~ YES 4 x Bolts & Washers ~ BOLTS YES/WASHERS NO

Works as they should no issues with them

Bought these alloy mounts to replace the plastic ones that came with the aux driving lights I installed on my motorcycle a few years ago. I was tired of constantly repositioning and tightening the lights because of the cheap mounts they came with not holding well. These are great and could be used for many applications! Well worth the money