Carbon Fiber Repair Kit, 36" x 6" | Includes 3K 2x2 twill carbon fiber fabric & 8 oz epoxy resin.

I have a giant escape composite left it locked on a fence and someone tried to steal it and damaged the frame by the seat post , cracked the frame so pad the seat post was leaning . I used the sheets and epoxy to repair the frame. I let it dry for a couple days then applied another layer. repeated the process about 4 or 5 times. this happened in 2021 and its 2023 now and the seat post is sitting sturdy in the frame like new. had to write a review excellent product for repairing carbon fiber frame

I used this product to repair a cracked top tube on my carbon fiber bike. I found, and followed, some videos I found on YouTube on repairing a bike using carbon fiber. I would highly recommend buying some heat shrink wrap to use on the carbon mesh after you've applied it. If you've worked with fiberglass before you'll find that carbon fiber is nearly identical. I used small pieces and took my time in placement of them. I didn't wear gloves and didn't get any of the resin on my fingers. If you let the resin get sticky before you attempt to lay the fiber weave you'll find that it sticks quite well and stays where you put it (I laid down 3 pieces). After the carbon was laid in place and resin applied, I wrapped the area with plastic, then with duct tape, and, finally, heat shrink wrap. After heat shrinking with a heat gun, I let the material dry for around 30 hours. It set up perfectly and required minimal sanding. I was very pleased with the outcome!

If you are new to working with carbon fiber, here are a few things I’ve learned! This was my first time so I’m sure these are obvious to people who have worked with this material before. First the instruction don’t say it, but remove the yellow string. When you apply the epoxy you want to feather the fiber out as much as possible. Keeping the string on will create weird edges. Apply with a paints brush on small areas at a time, pressing firmly down to make sure the fiber is against the actual surface and not hovering in epoxy. I would try to buy some type of clear film so that you can smooth the surface down while it’s curing. I didn’t and just have a lot of sanding to do, but if you used like cling wrap with painters tape I think you could get a better result! Mark of your area, with the tape, apply the carbon and epoxy, then clickers film over that and smoothhhhh out. It feels strong on my surfboard! We will see!

This is my first attempt to work with carbon fiber. I broke my bike frame (I fell of a trainer... Long story) so my frame was cracked (sounds like when you are bending wood). After some research, I found that my frame was repairable, but it was expensive ($500 to $800 quotes). After daydreaming with a new bike, I felt like I should give it a try and repair the frame. I love my bike (Fuji SST 1.3) so, I set aside time and begin to sand the area, to discover there was a hole in the frame (see picture), and a crack around the entire tube. Did some research on how to repair the frame, got me some sanding papers (get the 3m 80 if you want to speed up the process) and begin my journey. Word of advice, get some single blade or an Xacto blade-like, scissors are a bad idea as this carbon sheet its very flimsy. I mixed the hardener and resin equally or 1 to 1 (It was a guesstimate). With a 1.5 brush, I start applying the epoxy and 10 minutes later I glue the carbon sheet (keep mixing the expoxy or it will bee to hard), gave it a second top coat and with a plastic bag, I squeeze it all the air and tape the bag very tightly and leave it 24 hours (air-conditioned indoor). Next morning, I unwrapped the repair (see picture of a very corrugated repair) and with an 80 grain, started sanding all that. Then with a 240 started smooth things out until I got rid of the rough edges and it was smooth. Finished up with an 800 (or could be 600) and gave it a light epoxy coat with a 1.5 brush (do not reuse the brush) and there you have it. With less than $50 I repaired a frame that looks good and will serve me well for years to come.

I used these materials to repair the seat stay on my wife's Trek. The package contains enough carbon fiber for a very large number of small repairs like this plus some 2 part epoxy, probably enough for 4-5 such repairs. I used a two stage process, applying the 1st layer, letting it dry overnight, lightly sanding the first layer, then applying the 2nd layer. A critical success factor is using heat-shrink release tape to compress each layer. This is a "must do" part of the process. Lay up the wet material and immediately wrap the tape tightly around the repair and shrink the tape with a heat gun on low. (Wrap with the outer side of the tape on the repair, opposite of how you would usually use tape, because the PTFE side is "out".) This tightly compresses the material, aiding in mechanical adhesion and creating a relatively smooth surface that only requires light sanding. I found 100 yds of Hi-Shrink Release Coated tape for about $28 delivered. So now I have enough tape and carbon for about 75 more repairs :-) Remains to be seen how the repair will hold up over time and under stress, but for now everything looks great and seems to be strong.

I like it and it is what I ordered, the only thing I don’t like is that tape around the carben sheet. I don’t see it serving any purpose.

This product worked great for my carbon bike frame repair. I made the repair much thicker than I may have needed, because I am very concerned of the strength of the repair. This product arrived in the mail quickly. The resin was slow to cure and needed nearly two days to fully cure; but this gave me a lot of working time with wrapping the layers of carbon weave and with removal of trapped air bubbles. I suggest using very sharp scissors to cut the carbon weave that's wetted with the resin on pattern marked parchment paper; or else it will fray apart on you. I practiced on a broken carbon fishing pole before doing my bike. The bond strength and repair strength was excellent on my fishing pole test piece. The bike frame repair is holding up well so far with 300 miles of rough LA roads and my 230 lbs weight.

I mixed the hardener and resin as instructed, but after 5 days it is still sticky. I able to easily take off the carbon patch. I guess batch where the product doesn't work. Carbon Fiber looks good, the resin is the problem. Also, there is no one to call for questions, any question seem to go through amazon. DON'T BUY THIS PRODUCT, IT IS A WASTE OF TIME AND MONEY