StarTech.com 40 Pin IDE to SATA HDD/Optical Drive Converter Adapter IDE2SAT2

古い機器を動かすのに古いノートパソコンを使用する事になり余っていたSATAのSSDを使用するために購入。 作りもしっかりしていて問題なく使用できています。

今となっては、珍しいコンバーターですが、使用に問題ありませんでした。 商品によっては、IDE接続で問題がでたりした経験があるので、よかったです。 電源供給も、汎用のフロッピー電源４ピンコネクタです。 個人的なお願いですが、コネクターの機能を左右入れ替えてほしいです。

外付けで持ち出しに重宝してます。 コスパでかなりお得です🉐

WDのM.2型SATA SSDが余ったので買ってみました。M.2そのままの時と比較してもアダプタによる速度低下などなく、問題なく使用できています。１つ用意しておくと便利かと思います。 商品写真で見えている基盤側が通常下向きになるので、底面固定だと7mm厚以上になるようなヒートシンクなどは使用できません。ご注意ください。

旧式3.5インチを２．５インチHDDを変更に使用した 動作良好でした

全くの不良品でした。セットしたM.2 SSＤは高熱で破壊寸前の上、複数のパソコンで認識しなかった。後日返品の手続きをします。

「注：M.2 NVMeまたはAHCI PCI-Express SSDは非対応」この記載を見落として互換性がなかった。

SSD なので、600までですが、HDDと比べたらはやいです。次は M.2 に挑戦します。

This product is fantastic. Much better than the cheap options available on facebook. Upon receipt I was blown away by the weight of the product compared to the cheap one I was sending back. Typical Startech quality on full display here. The Good: - Works seamlessly in an original xbox to allow for the use of massive SATA drives (I used it to max out the 2TB limitation of the hardware) - Made with good materials - Includes a molex passthrough to chain the adapter between a source and another drive - Includes jumpers to allow master/slave/cable select - The power adapter attaches parallel to the board, freeing up space in otherwise craped situations The Bad: - Both sides of the board is left entirely exposed, inviting shorts. Would highly recommend taping off the back of the board, regardless of use - The power cable uses the mini-molex plug used by legacy floppy drives, meaning you need to use the included cable to power the adapter. Not a deal breaker, but extra, unnecessary, wires always suck The Ugly: - As opposed to a standard plastic ATA socket, this adapter uses a pin header. Your IDE ribbon will fit fine, but it seems to attach muss less sturdy This device is 300% of the price of competing cheap options, but it is largely worth it to have a one-and-done solution. If you're looking to upgrade your original xbox hard drive in 2021, you really can't go wrong with this.

This is for the bi directional Sata <> IDE adapter. I only tested this by connecting IDE drives to my Sata only motherboard. It does what it's supposed to. 1/4 IDE drives were working and in excellent condition, the others were showing signs of head failure (clicking, freezing) which is probably due to the age of the drives and not the fault of this adapter. The way the adapter attaches to the drives is very tight and because of how far back it extends from the drive, it is very easy to snap off the ide connector on the drive if you're not extremely careful. You will have to attach the other cables beforehand to avoid stressing the hdd ide connector. Nearly everything you could possibly need is provided. A single Molex+ , Molex- and FDD power connector cable takes input molex from your power supply, the other molex connector goes into the drive and the FDD connector powers the Startech adapter itself. A sata cable (provided) then connects the adapter to the motherboard. If you don't have spare molex psu cables like i did, you will need a sata to molex adapter. The device itself has an led that sometimes lights up orange and other times red. It would have been nice if the manual indicated what these leds indicate especially with my faulty drives.

Najważniejsze, że ze starym kontrolerem IDE nowy napęd DVD działa, co prawda jeden - tak jakby przejściówka zapisywała sobie go (ten pierwszy napęd podpięty do niej) w pamięci i już żadnego innego nie chciała rozpoznać (jakaś metoda na jej reset?).

Utilisé pour mettre un nvme m2 Sata dans un acer V3-771G-32326G1TMaii. Fonctionne correctement et sans problème. Je précise pour ceux qui auraient des doutes : vous devez mettre un m2 sata, (par exemple : VERBATIM Vi560 S3 M.2 Sata) et non pas un m2 pcie(par exemple : WD_BLACK SN850X SSD).

I've used a few of these in Windows 98 gaming PCs that only support IDE. It means that all of the SATA HDD's I have lying around can be installed in these retro systems, as IDE drives are hard to find and overpriced these days. There are some operating system and hardware limitations of your retro system if you wish to use larger SATA drives, so be prepared to use something like Seatools to "trick" your larger SATA drive into thinking it's only 128GB/137GB in capacity for Win98 usage for example.. I've tried cheap ebay copies of this item and they are intermittent, it's not worth the hassle, spend the money on this for a reliable and great experience ;-)