ATX PC Case, 6 PWM ARGB Fans Pre-Installed, 360MM RAD Support, Type-C Gaming PC Case, 270° Full View Tempered Glass Mid Tower, Pure White ATX Computer Case,Y6

Overall the case is very nice and arrived in perfect condition. All six of the stock case fans work fine. If you're not going with liquid cooling and plan to add more fans like I did, I would suggest moving the two side intake and the rear exhaust down to the bottom. Leave the other three on the top. The reason for this is that the stock fans are 6pin and connect to an adapter cable that has your 3pin argb and 4pin pwm. There are two adapters cables, each of which connect 3 fans, but each branch that connects to a fan is pretty short, and spreading the fans apart will make it near impossible to connect all of them. As others have mentioned, a full atx board goes right to the bottom of the case. You'll only be able to fit flat cables under the board, and even that is a bit challenging. PLAN YOUR WIRING OUT AHEAD OF TIME AND GET YOUR CABLES IN PLACE BEFORE INSTALLING YOUR MOBO. You'll never fit anything under there once the mobo is in place. The rear chamber was spacious enough for all of the excess cable, granted I didn't install any drives back there. I'm no expert at cable management, but I was able to get everything tucked and tied without having to force the back on lol. I ended up using the HDD compartment in the top right for a fan hub. This is a very nice looking case and has a spacious interior for airflow. If you plan everything out ahead of time you shouldn't have too much trouble.

Very good case would definitely recommend it has plenty of room plenty of air flow easy to open glass door. Fit atx very good I seen post it was tight fit but it’s not maybe getting usb wire to front if you don’t pre wire it first like I did but you can loosen the bottom screws or press down at bottom and slide it there other than that pretty good wire management. I liked it so much I was gonna build and sell I ended up moving my components over to it as my daily gaming pc. Also the fans are very quite and the air flow is perfect.

I wanted a white build with glass case to show it off, and ended up with this Musetex case that checked all the boxes for me. The case was well packaged from the factory and arrived in perfect condition. I took advice from other reviews here and used a micro ATX board to give me space for wiring, and that ended up being the right call. It came with 6 matching ARGB fans that work perfectly with my fan hub and Gigabyte's RGB Fusion software. The glass panels are real glass, fit like a glove, and I also love the magnetic dust filters on the top and bottom that are very well cut, fit the recesses perfectly and are nearly invisible. My Red Dragon 850W PSU fit fine, and all mounting hardware needed to install the MB was included. My only wish were that it came with rubber grommets on the larger openings, but for the price, this is still a great deal. Very happy with this case.

The pros: good looking, solidly built, quiet fans, air flow, dust filters, easy to assemble, price. The cons: build space, cable cutouts, cable management. This is a good case overall, but it’s definitely best for a *MICRO ATX* motherboard. You can use a standard ATX, but space is limited. I think cases need silicon cable cutout liners (to hide where the cords are stored and eliminate sharp edges; aesthetically more pleasing). Also, there are no cutouts and absolutely no space at the bottom, if you’re using an ATX MB (standard/full size MB), to route cables which, if you’re a stickler for cable management/going for the neatest look you can get, you’re better off spending a little extra for a case that has those features. This is my first build, and it wasn’t so bad that I couldn’t finish, but I will likely upgrade cases somewhere down the line for a more user friendly and cleaner looking case. Overall, great case for the price and I believe this might be one of the best (price to performance) if you’re doing a micro ATX build.

This case is perfect, its fishtank design really highlights your components inside, it has a lot of cable management space in the back. The design of the case is mostly toolless, you can easily take off everything you need with your hands. The fans are great for this case price, they are argb and gen 2 rgb, and they are silent, even at full speed you can barely hear them, and it still keeps my pc cool, it never goes above 80 degrees.

A good case, the fans that come with it work as intended! Love the color and how easy it was to set up everything. The airflow is perfect for the modern beefy and hot cards

I purchased this PC case several months ago and I absolutely love it. It is great for new time gamers or PC users. Very easy to take apart and build/customize your PC. The size is perfect for the two desks that I've had, and I would definitely recommend.

With the right fan setup, the airflow is pretty dang good. The case came with 5x Musetek argb fans but I only ended up using 3x and then adding 6x Thermalright argb fans. Temps rarely ever go over 60c for cpu and gpu. Although, I’m only using an i5-10400 and an rtx 3060. The case looks spectacular though. I admit there wasn’t much confidence when ordering but after building in it, the quality is high and well put together. The only downside is that when putting a rear fan, the case will vibrate/hum at certain rpm. I’m using a Thermalright TL-C12W-S argb fan and when it’s around 1000rpm, you’ll hear a hum from the case. Any less and any more and there’s no humming. I have this fan in two other builds in the house and they don’t hum at this rpm. I’ve swapped and still get humming. Oh well, not deal breaker as you have to be sensitive of hearing to notice it.