Professional Aluminum Anodizing Pigment Dyes | Black E-CRO | Light to Rich Black | Powder Concentrate Makes 7.6 Liters or 2 Gallons

This anodize was fantastic. I can't say anything better about it. If you PROPERLY clean/ rinse. PROPERLY anodize your part. PROPERLY heat up the dye and let it soak for roughly 20 minutes. PROPERLY seal it in a light boil of water. Your product will come out great. If you want the anodize to have a 'shiny' look, polish your product and then clean it before your annodizing process.

RIT doesn't work. Don't do it. This is expensive but worth it. Don't waste time with RIT like I did. I ended up with gritty, splotchy, barely-dyed, reddish parts. I thought I was doing something wrong. I was. I was using RIT dye. After switching to this, my parts went from "I don't know what I'm doing" to "anodizing master". Don't make the mistake I did.

This is my first attempt ever to anodize aluminium. It took over a month to receive this dye (the nickel acetate sealant only took a week) but this is a good product. I tested this on a 1x2" piece of 6061 3mm aluminium suspended with non-anodized 2.5mm wire (both off Amazon). I buffed it and cleaned in hot water with some detergent, then 30 seconds in 2% sodium hydroxide @30'C, then 90 minutes anodizing at 4.5ASF (485mA/dm2) @24'C - for this piece that amounted to 160mA (Low Current Density method recommended by Caswell). I used 2 thin (1mm) strips of aluminium for cathodes (40mm x 110mm) - for my largest pieces this gives an anode:cathode ratio of 3:1 but in this small test it was closer to 1:5. I used sodium hydrogen sulphate (22.5%) which is equivalent to 16% sulphuric acid. I dyed for 15 minutes @60'C then sealed in nickel acetate for 15 minutes @99'C. I only mixed 1/6 of the dye (10g dissolved in water to 1270ml @82'C) and 1/6 of the nickel acetate too.

TLDR; this dye works spectacularly-if your setup and anodizing methodology is sound. Otherwise it sucks, but that's not the dye's fault. At first, I did NOT like this dye very much. It was super fussy-the color was about as deep as a puddle, the dye time had to be incredibly long to get much of any results, heating it up is a pain, the pH has to be in a certain range, these rather expensive bottles only make 7.6L of the stuff, etc. I was getting pretty tragic results even after a week and a half of testing, and the final nail in the coffin that cemented my distaste for this dye was that it began clumping up, leaving fugly marks on my parts. I switched to Rit for a bit, and it worked a little better, but I still wasn't getting good results. I was following the instructions on the bottle for this dye to a T, or so I thought... However, after heating the dye up to about 80°C and mixing it around thoroughly, the game COMPLETELY flipped on its head. It removed the clumps and the more thorough mixing allow it to work as intended, and boy does it work now! The pictures should speak for themselves. I cleaned up other aspects of my anodizing procedure and it works amazingly well on these bead blasted parts. For reference, I'm using a 20% sodium bisulphate (aka NaHSO4 aka pH decreaser for hot tubs and pools) solution for anodizing the parts, following the 720 rule for current and anodizing time, and I'm using the instructions on the bottle for the dyeing step. A distilled water rinse is done between bath changes. If you want to use this dye, especially if you're new to anodizing aluminum, be prepared to experiment. A lot. A ton. Dozens of times. Be patient and double check your setup. You can always strip off a bad anodizing job with 3 minutes in a 2% lye (NaOH) solution and try again. Get the process right on some scrap parts before doing production runs. Check the pH of your solutions periodically. WEAR SAFETY GEAR. And most importantly, don't give up hope until you've exhausted all viable options! Black in aluminum is hard to get right. There are no guarantees it'll work out for everyone of course, but I was ready to slam this stuff in this review 3 days ago-and now I'm telling you it's worth the price of admission. That should say a lot about the quality of this dye! Ngl though it IS super annoying to get it working as intended, but that's mostly my lack of experience showing more than anything else.

This dye penetrated my anodized aluminum evenly and permanently. I should add a note for the curious: After diluting the powder in water and using it for my project I decided to save the liquid in a giant Mason jar, thinking I would use it again. One year later I located the jar in the back of a cabinet and discovered a healthy colony of mold growing on the surface. I disposed the entire contents of the jar so I can't report about the effectiveness of the dye.

The results are very disappointing. Followed directions and the first of six parts came out fantastic with a deep black, second part had red undertones. The same protocol was used for both parts in the processing. I cannot recommend this product for more than a single part with a surface area less than 64 square inches. Look for and purchase a liquid dye that is not RIT. There is no difference in the outcome with this powdered dye and RIT. Waste of time and money. Buyer beware.

I ordered 3 bottles of these dyes, black, blue and red. I got the black first, used it and it worked perfectly! The bottle was full to the top. I then got the red and the bottle was almost empty. Me being a rookie anodizer, I didn't realize black takes more dye than the other colors so it's normal for the red and blue bottles to only have a teaspoon or so in them. I called Interactivia's customer service number that's listed in their profile and talked to a VERY helpful guy. He's done anodizing himself and not only answered my question on why the red and blue bottles were only partially filled, he gave me some awesome advice on the anodizing process. To have customer service like that is amazing these days. I REALLY appreciated the quick response to my phone call and having a helpful person on the other end. Thanks!

If you want a product that works AMAZING this is the product. Yes it’s a bit more expensive but 10% worth it. I tried dying our RV cushion covers I used 4 large bottles of another brand it didn’t touch it. Took a chance on this one and WOW it took the color like a dream. I was so happy it made them exactly how I wanted them. Can’t say enough how great this is ..run don’t walk to this product if you need to dye something.

Used to anodise some aluminium and works perfectly

Temp between 140F and 150F, soak for 15 Min and boil in water for 15 Min.

Dye fades on sun even after treating in NA for an hour at 200⁰F.. finding another solution cause this is a waste of precious time and money

Looking at the other reviews for this product I did not have high hopes but it worked pretty well. It was difficult to mix and I found that the dye in the bottom of the canister was clumped together and I had to scrape it out to get it all. But once I had it all mixed it worked great